angle of curvature

Adaptive slicing is realized by the calculation of the position of tangent plane of modeling surface, the angle of between the normal section line and the slicing plane, the curvature of normal section line in z-axis direction and radius of curvature.

计算出造型曲面的切平面位置、法线与分层平面的夹角、Z向法截线的曲率和曲率半径，实现优化分层。

互联网摘选

Mathematical formulas are derived comprehensively and systematically for the profile coordinate, pressure angle and radius of curvature of the cylindrical cam with an oscillating roller follower.

推导了摆动滚子从动件圆柱凸轮廓线、压力角及廓线曲率半径方程，讨论了该种凸轮机构在各种运转情况下与之相适用的方程。

互联网摘选

In this paper, with the principle of high pair replaced by low pair, the cam mechanism is transformed to linkage, through the analysis of the linkage the equation of the pressure angle and the radius of curvature and profile of cam is established.

本文运用高副低代原理，将凸轮机构转化为低副机构，通过低副机构运动分析建立起凸轮廓线、曲率半径及压力角表达式。

互联网摘选

Computation of S_1-stream sheet of axial air compressor with small installing angle by use of streamline curvature method

小安装角轴流压气机S1流面的流线曲率法解

互联网摘选

The article mainly discusses optical angular deviation affected by angle of incidence, curvature, refractive index and unparalleled faces in order to modify the windscreen processing.

本文主要讨论由上述因素引起的入射角、折射率、楔形度、厚度与曲率半径的比值对光学角偏差的影响，以利于生产工艺的控制。

互联网摘选

In this paper, the pressure angle and minimal radius of curvature of cam mechanism with swinging roller follower are discussed in details.

本文对摆动从动杆盘状凸轮机构的最大压力角和最小曲率半径问题进行了详细的讨论。

互联网摘选

Focusing on the research of some important design parameters impacting the carrying capacity of the bearing, including radial clearance, contact angle and groove radius of curvature coefficient, a detailed analysis was given, and the corresponding bearing design recommendations were presented.

着重对影响轴承承载能力的重要设计参数径向游隙、接触角、沟曲率半径系数等进行了仿真，并给予了详细的分析，提出了对应的轴承设计建议。

互联网摘选

Nozzle flow field of SRM was numerically simulated with Fluent software. The effects of nozzle convergent half angle, radius of curvature on upstream of throat section and length of throat cylinder on flow field are investigated.

用Fluent计算流体力学软件对固体火箭发动机喷管流场进行了数值计算，研究了喷管收敛半角、喷管喉部上游圆弧曲率半径和喉部圆柱段长度对喷管流场的影响。

互联网摘选

Water Flow Behaviors of Channel Bend in Middle Sized Radius and Big Bend Angle of Curvature

中等半径大偏转角弯道的水流特性

互联网摘选

The experimental results show that the total pressure loss and outlet derivation angle can be retained in an acceptable range when the bend angle of van rear end is less than a specific value, reaching the aim of adjusting the outlet angle of variable curvature cascade.

研究结果表明：叶片弯角小于一定值时，叶栅的总压损失和出口气流落后角保持在可接受的范围，能达到调节气流出口方向的目的；

互联网摘选